firmware download screen empty
Im experiencing y axis offset problems in 0.91 and went to download 0.92x but find your website firmware/download presents an empty web page. no download options available. can someone point me to...
View Articlemessage ERROR : EEPROM SUPPORT COMPILED
Helloi am new user arduinoI buy a 3 printer reprap x400 with arduino card 2560 ( it's not a new product)wen i use eeprom M commandM205, M206, M500, M501 and M502i have a message " ERROR : EEPROM...
View ArticleConfiguration
Hi All,is it possible to copy Config.h from AVR To Due vice versa?i also want to define the UI Pins in userpins.h , iknow to select AVR or ARM here.and a Question regarding pins :There are some pins...
View ArticleIs it possible to download the latest development version
Hi, is it possible to download the full file set for the development version (not using the Online Configuration tool)?I plan to make a firmware config for the BBOne/RADDS printer/controller
View ArticleIssues compiling firmware
Hi guys,I recently bought a 3d printer and it hasn't been working correctly. So the seller instructed me to update the firmware. They didn't really give any instructions and i've been struggling with...
View ArticleOlder Versions
Hello fellows,do you know where i can get older versions of the firmware ?I'm looking for 92.3 version but github merges versions and i can get it.Thanks in advance !
View ArticleNo response after shutdown
Searched the forum but didnt find anything about this =/I have a Da vinci 1.0A and just installed the repetier 0.92Im running simplify3d software.After I close s3d or press the disconnect button, or...
View ArticleFirmware update
Hi, i'm trying to update my firmware on my Zonestar Prusa i3 running off a Melzi 2.0 board.I used the Repetier 0.91 configuration tool (recommended for the firmware i was trying to install).I got the...
View ArticleFSR Auto level
Can anyone point me to a doc that describes how to set up auto level using 3 FSR sensors on a delta with repetier firmware? A brief description could help too if there is no doc. I can't seem to find...
View ArticleDual Z with different drivers
Hi. Im using a Megatronics v2 and would like to set up dual Z with 2 different drivers that would work in mirror. I selected extruder 0 to be Z but nothing happens. Any suggestions will be appreciated
View ArticleChange filament load/Unload speed and distance
HiWhere in firmware can I change the loading speed when I select the change filament option (no eprom"able" settings, no host, just printer)What is happening is that it loads to fast, and when the...
View Articleilios 3d printer
Hi everyone, new to the site and looking for information.As the title says I have recently acquired an ilios 3d printer, high quality I believe. but basically I have general basic back round in cnc and...
View ArticleDownload
I want to download he firmware... but the download page is empty, is this ok?Where is the configuration tool?
View ArticleAutolevel, homing and manual control problems
Ok, so I've got z-probe installed on Prusa i3 clone and it's working, more or less. First problem:Let's assume previous print ended at z = 100mm, there is no min z endstop, because probe is connected...
View ArticlePreheat?
Is there any way to preheat the bed and extruder automatically when I turn on the printer? I'm using a Da Vinci 1.0.Thanks
View ArticleDelta printer Auto Calibration
Are you planning to implement on repetier firmware a Delta Auto Calibration procedure? I have a big self made Delta that it is very long to calibrate due to the big plate area (500mm diam.).Thanks
View ArticleWill this work with adafruit motor controllers?
I have a audrino with two adafruit motor shields. Will I be able to control a diy printer with the firmware?
View ArticleFilament Use (amount used)
Printer: DaVinci 1.0AMac OSX ElCapitanArduinoRepetier Firmware 0.92When finished printing, the accumulated total of filament printed is displayed. I want to reset that amount (so I can track usage on...
View ArticleV0.91 does will not allow me to save the configuration.
Running V0.91 Rev 8.in the browser. I browse and select the v0.91 configuration file from my computer drive. Make changes. Click on the download page and it is blank.
View Article0.92.2 Powers off unexpectedly
So, I am running a Rostock Max V2 and on versions 0.92 and 0.92.2, after heating the hot end, as the temperature passes over the set temperature, and starts dropping as it starts to converge on the set...
View Article
More Pages to Explore .....